Spectrum-controls 1756sc-OF8H Series A Manuale Utente Pagina 17
- Pagina / 170
- Indice
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
Chapter 1: Module Overview 3
Diagnostic LEDs
The modules contain diagnostic LEDs that help you identify the source of
problems that may occur during power-up or during normal operation.
Power-up and diagnostics are explained in Chapter 9, Testing Your
Module.
System Overview
The modules communicate with the ControlLogix processor and receive
+5 Vdc and +24 Vdc power from the system power supply through the
backplane interface. You may install as many modules in the system as
the power supply can support.
The 1756sc-IF8H has 8 channels that can receive voltage and current
signals from volt or milliamp devices. When configured for volt or
milliamp analog inputs, the module converts the analog values directly into
floating point values. For those input types, the module assumes that the
input signal is linear prior to input into the module.
The 1756sc-OF8H has 8 channels that can output volt or millivolt signals
to drive field sensors.
Both modules support HART communication. Communication is
independent of the analog acquisition and control phase.
System Operation
At power-up, the modules check internal circuits, memory, and basic
functions. During this time the Cal LED remains on. If the module does
not find any faults, it turns off the Cal LED.
After completing power-up checks, the modules wait for a connection to
an owner controller then valid channel configuration data from your ladder
logic program. After channel configuration data is transferred, and one or
more channels are enabled, the module channels are available to your
ladder program.
Each time the 1756sc-IF8H reads an input channel, the module tests that
data for a fault, i.e. over-range, or under-range condition. If it detects an
open-circuit (wire off), over-range or under-range condition, the module
sets a unique bit in the status tags.
- Important Notes 3
- Table of Contents 5
- Table of Contents ix 9
- Terms & 12
- Abbreviations You 12
- Should Know 12
- Preface xiii 13
- Module Overview 15
- Chapter 1 15
- System Overview 17
- 4 ControlLogix 18
- Chapter 1: Module Overview 5 19
- 6 ControlLogix 20
- Power Requirements 21
- Using your module in 22
- Module Installation and 22
- Preventing 23
- Electrostatic 23
- Discharge 23
- Removal and Insertion 23
- Under Power 23
- Compliance to 24
- European Union 24
- Directives 24
- Wiring Your Module 26
- Preparing and Wiring 27
- Terminal Block Layout 28
- Wiring Inputs to the 28
- IF8H Module 28
- Wiring Outputs to the 30
- OF8H Module 30
- 18 ControlLogix 32
- Operation Within the 33
- ControlLogix System 33
- Chapter 3Chapter 3 33
- Chapter 3 33
- Direct Connections 34
- Module Operation 34
- Modules in a Local 35
- Requested Packet 35
- Interval (RPI) 35
- Modules in a Remote 36
- Listen-Only Mode 36
- Multiple Owners of 37
- Input Modules 37
- Configuration 38
- Changes in an Input 38
- Module with Multiple 38
- Chapter 4 39
- 26 ControlLogix 40
- Analog HART Modules 40
- 28 ControlLogix 42
- 30 ControlLogix 44
- Configuration Tags 45
- Overview 45
- 32 ControlLogix 46
- Input Tags Overview 48
- Output Tags 49
- (OF8H Only) 49
- 36 ControlLogix 50
- If8h0Configuration 52
- Table 5.1b 53
- 40 ControlLogix 54
- Table 5.1d 55
- 42 ControlLogix 56
- Amplitude 57
- 44 ControlLogix 58
- Table 5.3b 59
- 46 ControlLogix 60
- 1.) Select Controller Tags 61
- 3.) Select Monitor Tags 61
- Click on the tag name of the 62
- Configuration information is 62
- 1.) Highlight the value of 64
- 2.) Type in the valid new 64
- Of8h0Configuration 66
- Table 6.1b 67
- 54 ControlLogix 68
- Table 6.1d 69
- 56 ControlLogix 70
- Table 6.1f 71
- 58 ControlLogix 72
- Table 6.2b 73
- 60 ControlLogix 74
- Table 6.2d 75
- Table 6.3 75
- Use a pulldown menu 78
- Pulldown menu 78
- 66 ControlLogix 80
- 68 ControlLogix 82
- 70 ControlLogix 84
- 72 ControlLogix 86
- Table 7.1(Packet 0) 87
- 74 ControlLogix 88
- 76 ControlLogix 90
- 78 ControlLogix 92
- Get HART Device Information 94
- 82 ControlLogix 96
- HART Pass-Through Command 98
- 86 ControlLogix 100
- Analog HART Modules 100
- 88 ControlLogix 102
- 90 ControlLogix 104
- 92 ControlLogix 106
- 94 ControlLogix 108
- Short Frame Long Frame 109
- Master to slave 02 82 109
- Slave to master 06 86 109
- 96 ControlLogix 110
- 98 ControlLogix 112
- Programming Examples 113
- Chapter 8 113
- 100 ControlLogix 114
- Set Attribute All message: 116
- Module Reconfigure Message: 116
- 104 ControlLogix 118
- 106 ControlLogix 120
- 108 ControlLogix 122
- 110 ControlLogix 124
- 112 ControlLogix 126
- 114 ControlLogix 128
- 116 ControlLogix 130
- Figure 5.6a (Packed ASCII) 131
- 118 ControlLogix 132
- OK LED CAL LED Fault Status 133
- 122 ControlLogix 136
- 124 ControlLogix 138
- 126 ControlLogix 140
- 128 ControlLogix 142
- Maintaining Your Module 143
- And Ensuring Safety 143
- Chapter 10 143
- 132 ControlLogix 146
- HART Analog Modules 146
- Appendix A 147
- Environmental Conditions 148
- Regulatory Compliance 148
- Firmware Revision History 148
- Appendix B 149
- 140 ControlLogix 154
- 142 ControlLogix 156
- Appendix D 157
- 144 ControlLogix 158
- 146 ControlLogix 160
- 148 ControlLogix 162
- 150 ControlLogix 164
- 152 ControlLogix 166
- Table 3c (First Byte) 167
- Table 3d (Second Byte) 167
- 167
- 154 ControlLogix 168
- Getting Technical 169
- Assistance 169
- Declaration of 169
- Conformity 169
Prodotti e manuali riguardandi Strumenti di misura Spectrum-controls 1756sc-OF8H Series A
(118 pagine)Sealey Měřící nástroje uživatelské příručky
Seznam produktů Sealey Měřící nástroje obsahuje 59 uživatelské příručky pro 59 modelů. Všechny uživatelské příručky pdf jsou k dispozici ke stažení nebo prohlížení online.
Commenti su questo manuale